+- Indonesian Back|Track Team (https://www.indonesianbacktrack.or.id/forum)
+-- Forum: General Zone (https://www.indonesianbacktrack.or.id/forum/forum-172.html)
+--- Forum: Programming (https://www.indonesianbacktrack.or.id/forum/forum-95.html)
+---- Forum: Bash (sh) (https://www.indonesianbacktrack.or.id/forum/forum-96.html)
+---- Thread: Share Sedikit perintah shell untuk menguji Kecepatan HDD (/thread-5708.html)
Sedikit perintah shell untuk menguji Kecepatan HDD - zee eichel - 04-04-2014
Kembali lagi deh yang simple2 heheheh, ya ini cuma iseng sharring aja biar forum gk sepi , kita akan menguji kecepatan hdd device melalui perintah bash/shell
Timing cached reads: 5942 MB in 2.00 seconds = 2972.73 MB/sec
Timing buffered disk reads: 278 MB in 3.01 seconds = 92.46 MB/sec
dan jika hendak melihat temparatur
Code:
root@kali:/var/log# hdparm -H /dev/sda
/dev/sda:
drive temperature (celsius) is: 45
drive temperature in range: yes
Untuk ngecek CDroom ada perintah tambahan
lets start some code - Untuk latihan ya
buat file dalam ekstensi .sh
Code:
#/bin/bash
read -p "drive yang hendak di cek:" hdd
sleep 2
hdparm -TtgiH $hdd
[/hide]
ya semoga saja berguna walau cupu nih thread hehehe
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - zee eichel - 04-04-2014
(04-04-2014, 09:16 PM)Muhammad Naufal Wrote: makasih kang zico, gak terlalu cupu sih kang :-bd
hehehe makasih2
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - orang sederhana - 04-30-2014
(04-04-2014, 09:28 PM)zee eichel Wrote:
(04-04-2014, 09:16 PM)Muhammad Naufal Wrote: makasih kang zico, gak terlalu cupu sih kang :-bd
hehehe makasih2
om zee ada tutorial bash ngga ?? ane pengen belajar bash nih om :d :-bd
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - EKO_X - 04-30-2014
Saya baru mencoba install Zentyal Server 3.4 di VMware Workstation 10. Setelah selese installasi kenapa tidak muncul GUI nya ya
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - Track-R - 05-01-2014
wah mantep om zee :-bd nice share baru tau nih om kalo bisa seperti itu untuk mengecek kondisi disk.. soalnya biasa cuma menggunakan gnome-disk-utility aja om, ternyata bisa juga melihat kondisi disk melalui command line ya?
oh ya om zee tapi untuk mengecek(melihat) temperature dari hdd kita, hanya hdd dengan merk Hitachi aja ya yang bisa di cek dengan opsi -H itu om?
Spoiler! :
Quote:
Code:
hdparm - get/set hard disk parameters - version v9.37, by Mark Lord.
Usage: hdparm [options] [device ...]
Options:
-a Get/set fs readahead
-A Get/set the drive look-ahead flag (0/1)
-b Get/set bus state (0 == off, 1 == on, 2 == tristate)
-B Set Advanced Power Management setting (1-255)
-c Get/set IDE 32-bit IO setting
-C Check drive power mode status
-d Get/set using_dma flag
-D Enable/disable drive defect management
-E Set cd/dvd drive speed
-f Flush buffer cache for device on exit
-F Flush drive write cache
-g Display drive geometry
-h Display terse usage information
-H Read temperature from drive (Hitachi only)
-i Display drive identification
-I Detailed/current information directly from drive
-k Get/set keep_settings_over_reset flag (0/1)
-K Set drive keep_features_over_reset flag (0/1)
-L Set drive doorlock (0/1) (removable harddisks only)
-m Get/set multiple sector count
-M Get/set acoustic management (0-254, 128: quiet, 254: fast)
-n Get/set ignore-write-errors flag (0/1)
-N Get/set max visible number of sectors (HPA) (VERY DANGEROUS)
-p Set PIO mode on IDE interface chipset (0,1,2,3,4,...)
-P Set drive prefetch count
-q Change next setting quietly
-Q Get/set DMA queue_depth (if supported)
-r Get/set device readonly flag (DANGEROUS to set)
-R Obsolete
-s Set power-up in standby flag (0/1) (DANGEROUS)
-S Set standby (spindown) timeout
-t Perform device read timings
-T Perform cache read timings
-u Get/set unmaskirq flag (0/1)
-U Obsolete
-v Use defaults; same as -acdgkmur for IDE drives
-V Display program version and exit immediately
-w Perform device reset (DANGEROUS)
-W Get/set drive write-caching flag (0/1)
-x Obsolete
-X Set IDE xfer mode (DANGEROUS)
-y Put drive in standby mode
-Y Put drive to sleep
-z Re-read partition table
-Z Disable Seagate auto-powersaving mode
--dco-freeze Freeze/lock current device configuration until next power cycle
--dco-identify Read/dump device configuration identify data
--dco-restore Reset device configuration back to factory defaults
--direct Use O_DIRECT to bypass page cache for timings
--drq-hsm-error Crash system with a "stuck DRQ" error (VERY DANGEROUS)
--fallocate Create a file without writing data to disk
--fibmap Show device extents (and fragmentation) for a file
--fwdownload Download firmware file to drive (EXTREMELY DANGEROUS)
--fwdownload-mode3 Download firmware using min-size segments (EXTREMELY DANGEROUS)
--fwdownload-mode3-max Download firmware using max-size segments (EXTREMELY DANGEROUS)
--fwdownload-mode7 Download firmware using a single segment (EXTREMELY DANGEROUS)
--idle-immediate Idle drive immediately
--idle-unload Idle immediately and unload heads
--Istdin Read identify data from stdin as ASCII hex
--Istdout Write identify data to stdout as ASCII hex
--make-bad-sector Deliberately corrupt a sector directly on the media (VERY DANGEROUS)
--offset use with -t, to begin timings at given offset (in GiB) from start of drive
--prefer-ata12 Use 12-byte (instead of 16-byte) SAT commands when possible
--read-sector Read and dump (in hex) a sector directly from the media
--security-help Display help for ATA security commands
--trim-sector-ranges Tell SSD firmware to discard unneeded data sectors: lba:count ..
--trim-sector-ranges-stdin Same as above, but reads lba:count pairs from stdin
--verbose Display extra diagnostics from some commands
--write-sector Repair/overwrite a (possibly bad) sector directly on the media (VERY DANGEROUS)
(04-30-2014, 05:19 PM)orang sederhana Wrote:
(04-04-2014, 09:28 PM)zee eichel Wrote:
(04-04-2014, 09:16 PM)Muhammad Naufal Wrote: makasih kang zico, gak terlalu cupu sih kang :-bd
hehehe makasih2
om zee ada tutorial bash ngga ?? ane pengen belajar bash nih om :d :-bd
om @orang sederhana mungkin ini bisa sedikit membantu om, kemarin pas muter" cari e-book ketemu dengan e-book tentang bash programing didalam modul ini sepertinya seraca detail dibahas om.. tapi aku juga belum selesai bacanya.. \m/
monggo download di mari om
(*) Link Asli - Download Via Torrent
(*) Mirror - Download Via Dropbox
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - orang sederhana - 05-02-2014
(05-01-2014, 01:26 AM)Track-R Wrote: wah mantep om zee :-bd nice share baru tau nih om kalo bisa seperti itu untuk mengecek kondisi disk.. soalnya biasa cuma menggunakan gnome-disk-utility aja om, ternyata bisa juga melihat kondisi disk melalui command line ya?
oh ya om zee tapi untuk mengecek(melihat) temperature dari hdd kita, hanya hdd dengan merk Hitachi aja ya yang bisa di cek dengan opsi -H itu om?
Spoiler! :
Quote:
Code:
hdparm - get/set hard disk parameters - version v9.37, by Mark Lord.
Usage: hdparm [options] [device ...]
Options:
-a Get/set fs readahead
-A Get/set the drive look-ahead flag (0/1)
-b Get/set bus state (0 == off, 1 == on, 2 == tristate)
-B Set Advanced Power Management setting (1-255)
-c Get/set IDE 32-bit IO setting
-C Check drive power mode status
-d Get/set using_dma flag
-D Enable/disable drive defect management
-E Set cd/dvd drive speed
-f Flush buffer cache for device on exit
-F Flush drive write cache
-g Display drive geometry
-h Display terse usage information
-H Read temperature from drive (Hitachi only)
-i Display drive identification
-I Detailed/current information directly from drive
-k Get/set keep_settings_over_reset flag (0/1)
-K Set drive keep_features_over_reset flag (0/1)
-L Set drive doorlock (0/1) (removable harddisks only)
-m Get/set multiple sector count
-M Get/set acoustic management (0-254, 128: quiet, 254: fast)
-n Get/set ignore-write-errors flag (0/1)
-N Get/set max visible number of sectors (HPA) (VERY DANGEROUS)
-p Set PIO mode on IDE interface chipset (0,1,2,3,4,...)
-P Set drive prefetch count
-q Change next setting quietly
-Q Get/set DMA queue_depth (if supported)
-r Get/set device readonly flag (DANGEROUS to set)
-R Obsolete
-s Set power-up in standby flag (0/1) (DANGEROUS)
-S Set standby (spindown) timeout
-t Perform device read timings
-T Perform cache read timings
-u Get/set unmaskirq flag (0/1)
-U Obsolete
-v Use defaults; same as -acdgkmur for IDE drives
-V Display program version and exit immediately
-w Perform device reset (DANGEROUS)
-W Get/set drive write-caching flag (0/1)
-x Obsolete
-X Set IDE xfer mode (DANGEROUS)
-y Put drive in standby mode
-Y Put drive to sleep
-z Re-read partition table
-Z Disable Seagate auto-powersaving mode
--dco-freeze Freeze/lock current device configuration until next power cycle
--dco-identify Read/dump device configuration identify data
--dco-restore Reset device configuration back to factory defaults
--direct Use O_DIRECT to bypass page cache for timings
--drq-hsm-error Crash system with a "stuck DRQ" error (VERY DANGEROUS)
--fallocate Create a file without writing data to disk
--fibmap Show device extents (and fragmentation) for a file
--fwdownload Download firmware file to drive (EXTREMELY DANGEROUS)
--fwdownload-mode3 Download firmware using min-size segments (EXTREMELY DANGEROUS)
--fwdownload-mode3-max Download firmware using max-size segments (EXTREMELY DANGEROUS)
--fwdownload-mode7 Download firmware using a single segment (EXTREMELY DANGEROUS)
--idle-immediate Idle drive immediately
--idle-unload Idle immediately and unload heads
--Istdin Read identify data from stdin as ASCII hex
--Istdout Write identify data to stdout as ASCII hex
--make-bad-sector Deliberately corrupt a sector directly on the media (VERY DANGEROUS)
--offset use with -t, to begin timings at given offset (in GiB) from start of drive
--prefer-ata12 Use 12-byte (instead of 16-byte) SAT commands when possible
--read-sector Read and dump (in hex) a sector directly from the media
--security-help Display help for ATA security commands
--trim-sector-ranges Tell SSD firmware to discard unneeded data sectors: lba:count ..
--trim-sector-ranges-stdin Same as above, but reads lba:count pairs from stdin
--verbose Display extra diagnostics from some commands
--write-sector Repair/overwrite a (possibly bad) sector directly on the media (VERY DANGEROUS)
(04-30-2014, 05:19 PM)orang sederhana Wrote:
(04-04-2014, 09:28 PM)zee eichel Wrote:
(04-04-2014, 09:16 PM)Muhammad Naufal Wrote: makasih kang zico, gak terlalu cupu sih kang :-bd
hehehe makasih2
om zee ada tutorial bash ngga ?? ane pengen belajar bash nih om :d :-bd
om @orang sederhana mungkin ini bisa sedikit membantu om, kemarin pas muter" cari e-book ketemu dengan e-book tentang bash programing didalam modul ini sepertinya seraca detail dibahas om.. tapi aku juga belum selesai bacanya.. \m/
monggo download di mari om
(*) Link Asli - Download Via Torrent
(*) Mirror - Download Via Dropbox
wuuuiihh makasih banyak om @Track-R$ link nya . aku download ya hihih :d
sukses selalu temen temen IBTeam :-bd
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - Track-R - 05-02-2014
(05-02-2014, 12:12 PM)orang sederhana Wrote: wuuuiihh makasih banyak om @Track-R$ link nya . aku download ya hihih :d
sukses selalu temen temen IBTeam :-bd
oke om sama" monggo di dunlut.. :-bd
salam sukses \m/
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - orang sederhana - 05-02-2014
om itu torrent ya ? aduuhh ane ga kuat koneksi kalo torrent :'(
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - Track-R - 05-02-2014
(05-02-2014, 01:57 PM)orang sederhana Wrote: om itu torrent ya ? aduuhh ane ga kuat koneksi kalo torrent :'(
ada yang dropbox kok om.. udah ku mirrorin..
ngk gede juga kok file nya om..
RE: Sedikit perintah shell untuk menguji Kecepatan HDD - aspire89 - 05-02-2014